Search for:

Portable Gas Detectors

Rugged, compact and lightweight (less than 2 lbs.) with leather (belt-carried) carrying case Solid state sensor (Uses UL approved sensor)  Warranty 1 Year Accurate low ppm or % LEL readings Audio/visual alarm Low-battery warning light Built-in battery charger and rechargeable NiCad Battery (built inside the unit) (see comments below) Special charge cable, one end into AC line (110 or 220 volts) other end into input of unit Orange light comes on when charging (charge time overnight or 8 hours) Fast warm up time:  3-4 minutes ■Please be advised that the battery is built-into the unit (it's a rechargeable NiCad battery which provides 4 VDC power which gives the unit 10 hours of continuous operating capabilities at full charage).  It also has a built-in charger.  Use the cable provided that you plug into a 220 volt ac outlet, the other end is plugged into the unit.  When it is charging, then the charging light comes on.

These portable gas detectors are easy to use and can be used in any accessible area where gas concentration levels are a concern. Typical users include chemical industry and textiles, power plants, steel mills, oil and gas refineries, parking garages, sewage treatment plants, food/beverage industry, pharmaceutical industry, hospital and medical labs and many more. The rechargeable NiCad batteries provide 4V DC power which gives the unit 10 hours of continuous operating capabilities at full charge. The solid state sensors ensure stable, quick response and fast recovery. These models are capable of detecting gases at inert or low oxygen backgrounds. Price includes controller, probe with 6 ft cable, batteries, charge cable, leather carrying case and shoulder strap belt holder for the meter (weighs less than 2 pounds) and manual.

Specifications

Controller Module

Meter Range: ppm, 0-100% LEL (see order information for specific ranges)
Alarms: Visual red LED light, Audio buzzer 75 dB
Panel Controls: Zero and Span adjustments
Battery Charge: Built-in battery charger
Battery Signal: Visual Yellow LED (indicates low battery)
Operating Hours: 10 hours continuous
Operating Temp: 5° to 140° F
Power: 3.6V NiCad battery
Size: 7.4"H x 4.3"W x 2.8"D
Weight: 2 lbs

Sensor

Type: Solid-state, MOS, diffusion type
Operating Temp: 5° to 140° F
Sensor Life: Up to 3 years normal operation
Humidity Range: 5 to 95% RH
Response time <15 seconds to 80-90% FS
Recovery Time: <30 seconds for return 80% FS
Accuracy: ±5% of measured volume
Cable Length: 6 ft (optional up to 50 ft)

We accept credit card and Paypal orders online only from customers in the United States. 

*** General information on these EtO Gas Detectors.
General Information
Ethylene Oxide (EtO) is a commonly used sterilizer in various industries including medical equipment
suppliers, pharmaceuticals, museums and hospitals.  The sterilizer system basically functions as a
monitor to test the surrounding air for EtO levels.  The system can be either portable, or wall mounted,
depending on the user's need.  The alarm will monitor the EtO levels down to the specific ppm, and
employ both visual and audio alarms when the level has been exceeded.  EtO detectors must be
installed near the stabilizer in accordance with health and safety standards whenever EtO sterilizers
are in use.  The sterilizer must also be properly aerated after use.

Freon Gases Measured

3M Freon Gas Classified HFE-7100 (Catalog No. 51A76)

**Catalog No. 51A76 detects Freon gases R12, R113, R22, R123, R134A, R23, R114, R143A, R141B, R1113
as well as the following Du-Pont Fluoroproducts mixtures:
    Freon R404A (44% R125 + 52% R143A + 4% R134A),
    Freon R407C (23% R32 + 25% R125 + 52% R134A),
    Freon R507 (50% R125 + 50% R134A)

Note:  Du-Pont's products R404A or R507 to replace R502,
                                             R407C or R410A to replace R22,
                                             R134A to replace R12, R500
                                             R508B to replace R13, R503, R23
                                             R123 to replace R11

Kernco will now supply the Freon gas R-11.  We do this for those users who require the Freon R-11 gas.

For calibrating procedures and for listing of the various calibration gas mixture kits - CLICK HERE

IMPORTANT NOTICE - If you need a product and it has not yet
been set up for on-line purchase, please place your order by
credit card toll-free to 1-800-325-3875.  We will honor the prices
shown on the website.

Any problems or questions call 1-800-325-3875 or Email or fax to 915-852-4084.

 

Prices shown apply to sales to companies within the United States.

For sales outside the US contact Kernco Instruments for appropriate prices for your country.

  Hosting provided by 3N1 Creative  © Kernco Instruments Inc.